Electrical Stability Tester (EST) Model 194-02

(Electrical Stability Tester (EST) Model 194-02) The measurement of electrical stability (ES) is to apply a sinusoidal electrical signal with gradually rising voltage to a pair of parallel plate electrodes immersed in drilling fluid. The resulting current is very weak until it reaches a critical voltage, after which the current intensity rises sharply.
Product Description

China Electrical Stability Tester (EST) Model 194-02 manufacturers

China Electrical Stability Tester (EST) Model 194-02 suppliers

 

1. Product Introduction of Electrical Stability Tester (EST) Model 194-02

 

The measurement of electrical stability (ES) is to apply a sinusoidal electrical signal with gradually rising voltage to a pair of parallel plate electrodes immersed in drilling fluid. The resulting current is very weak until it reaches a critical voltage, after which the current intensity rises sharply.

 

The tester complies with the electrical stability test procedure described in API rp13b-2 Recommended Practice for field testing of oil-based drilling fluid. The instrument is mainly composed of an instrument box, test body, electrode, power adapter and glass beaker. It is accurate, simple and portable. The influence of the chemical composition and shear history of drilling fluid on the absolute value of ES is very complex.

Electrical Stability Tester (EST) Model 194-02

2. Product Application and characteristic of Electrical Stability Tester (EST) Model 194-02

 

The Electrical Stability Tester (DWY-2) is a sine wave instrument manufactured in accordance with the American Petroleum Institute (API) recommended Practice Standard Procedures for Field Testing of Oil Drilling Fluids 13B-2. It's accurate, simple and portable. Used for conventional field and laboratory measurements of relative electrical strength of drilling fluids with continuous oil phases. Dwy-2 tester consists of test instrument and probe, which is powered by four common 9-volt alkaline batteries. Dielectric breakdown voltage is the key to conductive drilling fluid. The battery's DC power supply provides an AC voltage to the electrodes at low frequencies.

 

The size of the electrical stability tester, the spacing between electrodes, and the current have all been standardized. The two electrodes are the same size, 0.061 inches apart; The current size is set as 61uA, the frequency of the continuously increasing voltage is fixed at 340 ±10Hz, and the sine wave with the continuously increasing amplitude is always loaded on the electrode. The electrodes are immersed in drilling fluid. If the current between the electrodes starts to run and increases to 61uA, the voltage automatically stops growing and the peak voltage reading stabilizes. The peak voltage is recorded and the breakdown voltage of the dielectric is displayed.

 

The electrical stability value will decrease with increasing test temperature, and the recommended API test temperature is 120± 5 ° F (49± 3 ° C). The chemical composition and shear process of drilling fluid control the absolute value of DWY-2.

 

Electrical Stability Tester (EST) Model 194-02

 

3. Product operate of Electrical Stability Tester (EST) Model 194-02

 

1). Filter the bulk solids in the sample with a 12-well test sieve or Markov funnel, and place the sample in a heated beaker or a heated viscosity cup.

 

2). Adjust and keep the container and sample temperature at 50±2℃, (120±5℉).

Note: Do not connect the electrode probe to the instrument!

 

3). Thoroughly wipe the electrode probe with a paper towel, and wipe several times between the electrodes.

 

4). With the probe to stir the oil base, to ensure that it can be used in the mud, if the oil base is not suitable, other oil or reagent (such as isopropyl alcohol) can also, before the test, wipe and dry the probe.

 

Agitate with the probe for at least 10 seconds and use a thermometer to ensure the solution temperature is 50±2℃ (120±5℉). Note: Do not move the electrode probe during the test!

 

Press the "test" button and the voltage starts to rise automatically. Do not move the probe during the test. The voltage stops increasing when the breakdown voltage is reached, at which point the voltage value is recorded as the dielectric breakdown voltage (electrical stability reading).

 

Note: If the instrument voltage reading is greater than 2000V, the breakdown voltage of this solution sample exceeds 2025±25V (peak).

 

Record and average the electrical stability of oil-based mud from two or more tests.

 

Note: this instrument will retain the reading from the last test. Press the reset button again to reset the reading to zero and start the next test.

 

4. Product maintenance of Electrical Stability Tester (EST) Model 194-02

 

1). Often wipe, keep the instrument without dust, away from corrosive liquid and solvent, ensure the durability of the instrument.

 

2). Avoid the probe slot and battery box of the instrument being exposed and splashed with liquid.

 

3). Put an end to the brutal operation of instruments.

 

4). Thoroughly wipe the electrode probe with a paper towel.

 

Electrical Stability Tester (EST) Model 194-02

 

5. Company Introduction of Electrical Stability Tester (EST) Model 194-02

 

China Haitongyuanda Special Instrument factory is a professional Electrical Stability Tester (EST) Model 194-02 manufacturer and Electrical Stability Tester (EST) Model 194-02 supplier. Our products are exported to dozens of countries and regions and are unanimously recognized by our customers. To order Electrical Stability Tester (EST) Model 194-02, choose China Haitongyuanda Special Instrument factory, a professional Electrical Stability Tester (EST) Model 194-02 manufacturer. Our company is committed to the R&D and manufacturing of drilling fluid analyzer, oil well cement tester, oilfield laboratory integrated engineering solutions and experimental instrument maintenance services. Over the past 40 years, with the care and support of oilfield users, experts from various industries and engineers and technicians, our products and technologies have been tested by the market making. Haitongda special analytical instruments have grown to world-famous brands. Our company has researched and developed testing instruments needed in unconventional oil and gas resources, deep water, natural gas hydrate and intelligent drilling, and successively produced a variety of new products, such as ultra-HTHP rheometer, drilling fluid online testing system and deep water low temperature drilling fluid testing system, which timely met the needs of technological progress in the drilling industry. At present, we are providing quality services and practical products to more than 3,000 customers in more than 20 countries and regions around the world.

 

6. FAQ

 

1): Are you a manufacturer or a trading company?

A1: We are manufacturer.

 

2): What is your main brand?

A2: Our brand is Haitongda, which is famous in China and other nation. Also we do OEM.

 

3): What are your business scope and product classification?

A3.Business scope. Mud analysis instrument, electronic products, special instrument, mold design and manufacturing; Instrument maintenance and sales, import and export of goods and technologies.

 

Product classification including drilling fluid analysis instrument oil ell cement testing instrument and field overall solution, including 22 small categories and over 120products.

 

4): What is your MOQ for the order?

A4: Testers per 1 set.

 

5): What is the warranty period of your instrument?

A5: One year.

 

6): Can l get better offer if our order can be bigger?

A6: Certainly. We will give you better prices based on the quantity for your order.

 

7): What certificate do you have for your instrument?

Q7: ISO, SGS and so on.

 

8): What is your lead time for our order?

A8: For new order: 3 weeks.

For stock order: 3 working days after T/T. Based on FOB Qingdao.

 

9): What is your advantage of your factory?

A9: We are the original oil ministry designated drilling fluid analysis equipment manufacturer in China, which was founded in 1968.

 

10): What is the process to become an agency?

A10: Please send us mail enquiry, then we will reply you as soon as possible.

 

Electrical Stability Tester (EST) Model 194-02 manufacturers

Electrical Stability Tester (EST) Model 194-02 suppliers

Send Inquiry
For inquiries about our products or pricelist, please leave your email to us and we will be in touch within 24 hours.

Verify Code